Best propellers and landing gear for DJI FPV?

For ur DJI FPV, I’d stick with DJI FPV Propellers (Pair)—honestly they’re the smoothest/most efficient; 3rd‑party is hit/miss and even tiny bends = vibes. For clearance, snap-on DJI FPV Landing Gear Extension Kit works ok—light, but adds drag a bit; avoid chunky 3D prints imo.

Story time: i went through this last year with my DJI FPV… one dumb little tip-over on asphalt and suddenly fast turns felt kinda “buzzy” and not as locked in. Turned out it was 100% props (one was barely warped… like you almost cant see it).

1) Props: OEM vs “upgraded” aftermarket
- DJI FPV Propellers: honestly these stayed the most consistent for me. When I swapped in a fresh set the vibration basically vanished immediately. The big “pro” is balance/fit is predictable; the “con” is they don’t love pavement kisses.
- Generic third‑party “DJI FPV compatible” props (idk brand… Amazon special): mine were a mixed bag. One set was louder and had this faint oscillation at higher throttle… i guess balance/tolerances. Pro: sometimes a bit tougher plastic. Con: more variance, and the quad felt slightly less smooth.

2) Landing gear / clearance: low-profile vs tall legs
- Low-profile TPU skids/arm guards (3D printed style): i ran a set and was actually happy. Pro: protects on grass/hardpack and spreads the scrape. Con: if it’s chunky it can catch airflow and you’ll feel a tiny bit more “float.”
- Taller snap-on legs (not the popular extension kit mentioned already): i tried a taller set once and it helped the camera clearance a lot, but ngl it felt more draggy in fast forward flight.

But yeah… for me, fresh props fixed 90% of “mystery vibes.” good luck, cheers

Seconding the “swap a full prop set” advice—seriously, tiny bends = vibes + extra stress. I’d stay OEM: DJI FPV Propellers and keep 2 full sets (~$15–$25). For clearance, go minimal like STARTRC DJI FPV Landing Gear Leg Extenders (light, less airflow drama); avoid chunky 3D prints, they can get weird in fast turns.

I've been flying this rig for over a year now and honestly - after burning through a few dozen sets - I stopped buying OEM. I moved to Master Airscrew DJI FPV Ludicrous Propellers because they’re significantly tougher. The stock props are fine for cinematic stuff, but they’re pretty brittle; one clip on a branch and they shatter. These ones have saved me from a walk of shame more than once. Regarding the clearance, I actually moved away from the 'stilt' style legs after a few months because they create a weird pendulum effect in high-speed maneuvers. I swapped to the PGYTECH DJI FPV Landing Gear which is a bit more stable, but if you're really worried about the camera, check out the Sunnylife DJI FPV Gimbal Bumper. It’s basically a roll bar for your camera. It doesn't give you vertical ground clearance, but it stops the pavement from eating your lens if you tip over, and it doesn't mess with the aerodynamics or center of gravity nearly as much as the big leg extensions do.

Coming back to this with some data-driven suggestions for long-term savings! If you want to maximize your budget while maintaining high technical performance, you should definitely consider switching to specialized polycarbonate blends. They are much more resilient than standard materials!!

• Gemfan 5328 Propellers for DJI FPV
• These provide incredible value and durability. The airfoil design is highly efficient and the polycarbonate material handles those minor pavement tips much better than the stock plastic ever could. Plus, they are way cheaper when you buy in bulk.
• BRDRC DJI FPV Heightened Landing Gear
• This is a fantastic budget-friendly option that adds roughly 30mm of clearance. It is lightweight enough that the flight controller barely notices the change in inertia during fast maneuvers, and it wont break the bank. I love using these because they are so affordable to replace and keep your gimbal safe! Just make sure you are checking your motor bells for any vertical play after a crash, as even the best gear wont fix a bent motor shaft if the impact was hard enough... stay safe out there!

Agree that most of that vibration is usually just a tiny warp in the prop you can barely see. One DIY tip I'd add is to really check the motor bells for any vertical play or grit while you have the props off. If you've tipped it over on pavement, its so easy for a tiny grain of sand or a slight shaft misalignment to mess with the gyro and cause that buzzy feeling. Honestly, do a full motor health check yourself before you worry too much about landing gear. If the motors are sound and you keep fresh props on there, the quad is usually rock solid. Better to spend five minutes inspecting the hardware than trying to fix a mechanical vibe with software or accessories.

- In my experience, 99% of that “buzzy fast turn” vibe was a barely-warped prop—cheap fix: swap a full set and keep a balanced spare set.
- Landing gear wise, I tried a light snap-on style and a chunkier printed one… the heavy one felt DRAGGY and messed with airflow, ngl.
- Budget tip: do props first (MOST value), then add the smallest clearance bump you can live with.

To add to the point above, unfortunately I've had nothing but issues with those snap-on landing legs. They're just not as good as expected because they turn the drone into a kite. I was really disappointed with how much they messed up the handling in a light breeze. Totally ruined the performance for me. Honestly, just get a PGYTECH Drone Landing Pad Pro and skip the extra weight on the frame. It's a much cleaner way to keep the gimbal safe without adding drag. As for props, I got fed up with the stock ones being so brittle. If you use an M5 adapter kit, Azure Power JohnnyFPV Freestyle Props are super tough and handle those pavement tips way better. You'll have to mess with adapters, which is a bit of a pain, but the durability is night and day. Dont bother with the cheap Amazon knockoffs tho, they're usually unbalanced right out of the box and will just give you more of those vibrations you're trying to fix...